Register Now: Advances in Spectroscopy for Pharma and Biopharmaceutical Analysis Symposium
|Articles|December 1, 2014

Spectroscopy Supplements

  • Special Issues-12-01-2014
  • Volume 29
  • Issue 12

Distinguishing Release Agents on Molded Rubber Using ATR Spectroscopy

Molded rubber products, like o-rings and gaskets, are typically coated with a release agent during manufacturing to facilitate the removal from the mold. Detecting the release agent is important for manufacturing since improper application can cause the o-rings to adhere unexpectedly to the mold.

Measuring the release agent on molded rubber products by infrared spectroscopy presents several challenges because the release agent layer is typically very thin and many base materials are carbon filled, and molded into small or unusual shapes. Thus, analysis requires a surface sampling technique with a relatively small sampling area, such as single-reflection ATR.

This applications note demonstrates the use of ATR to distinguish o-ring release agents from the underlying fluoroelastomer.

Experimental

A fluoroelastomer o-ring was investigated using the Harrick MVP-Pro in conjunction with a commercial FT-IR spectrometer. The MVP-Pro, shown in Figure 1, is a single reflection ATR accessory with a 45° incident angle and a 0.5 mm diameter sampling area on its Si crystal. All infrared spectra were collected with an 8 cm-1 resolution, averaged over 32 scans. Two spectra were recorded: one of the exterior of a black fluoropolyer (FKM) o-ring and another from the interior slice of the o-ring.


Figure 1: The Harrick MVP-Pro.

Results and Discussion

Figure 2 shows the ATR spectra of the FKM o-ring, including the outer surface, the inner substrate, and the resulting difference. The measured spectra show characteristics typical of a poly(aliphatic) fluoride, as expected. The strong similarity between the spectra indicates that the release agent coating the o-ring is extremely thin. Slight spectral differences can be seen around 1020 cm-1 and 800 cm-1. Subtracting the two spectra results in the spectrum shown in black, which is clearly identifiable as silicone oil. Silicones are one of the materials frequently used as a release agent.


Figure 2: ATR spectra of the o-ring: exterior (blue), interior (red) and subtraction result (black).

Conclusion

From the infrared spectra presented here, it is clear that the release agent can be distinguished from the bulk molded rubber using Si micro-ATR methods and the MVP-Pro.

Harrick Scientific Products, Inc.
141 Tompkins Ave., Box 277, Pleasantville, NY 10570
tel. (914) 747-7202, fax (914) 747-7409
Website: www.harricksci.com


Related to this article

San Francisco skyline with Oakland Bay Bridge at sunset, California, USA | Image Credit: © JFL Photography - stock.adobe.com
The January 30–February 4 event is expected to feature more than 4,500 presentations across six technical areas and more than 1,400 exhibitors at the Moscone Center.
A robotic arm in an automated agricultural setting, carefully processing a conveyer belt with tomatoes and leafy greens for food production. | Image Credit: © Donnangelo - stock.adobe.com
Croatian researchers outline how optical emission spectroscopy (OES) can track reactive species and plasma parameters in real time, giving processors a path to move cold plasma treatments from the laboratory to production lines.
Spectroscopy Top 10 DOI Articles of the Month (October 2026)
The following articles are the most accessed digital object identifier (DOI) manuscripts for Spectroscopy and LCGC International during the month of October 2026. Nine articles are individually ranked here by DOI page views; the seventh-highest entry (99 views) was recorded against the bare LCGC North America journal-level DOI rather than an individual article and is therefore not attributable to a single manuscript.
Mapping Molecular Mobility Pixel by Pixel
Garth Simpson of Purdue University explains how patterned photobleaching and spatial Fourier transforms can turn a single-point measurement into a diffusion coefficient at every pixel in the field of view.